adding some configs

config.ini

@@ -0,0 +1,67 @@
+acceleration = 0
+bed_size = 140,140
+bed_temperature = 95
+bottom_layer_speed_ratio = 0.3
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 75
+cooling = 0
+disable_fan_first_layers = 1
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid = 1,1
+end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\nM140 S0; turn off bed
+extrusion_axis = E
+extrusion_multiplier = 1
+extrusion_width_ratio = 0
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 2.75
+fill_angle = 45
+fill_density = 0.3
+fill_pattern = rectilinear
+first_layer_bed_temperature = 95
+first_layer_height_ratio = 1
+first_layer_temperature = 230
+g0 = 0
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor = reprap
+infill_acceleration = 50
+infill_every_layers = 1
+infill_speed = 75
+layer_gcode = 
+layer_height = 0.4
+max_fan_speed = 100
+min_fan_speed = 35
+min_print_speed = 10
+notes = 
+nozzle_diameter = 0.5
+output_filename_format = [input_filename_base].gcode
+perimeter_acceleration = 25
+perimeter_speed = 75
+perimeters = 2
+post_process = 
+print_center = 70,70
+retract_before_travel = 2
+retract_length = 1
+retract_lift = 0.4
+retract_restart_extra = 0
+retract_speed = 30
+rotate = 0
+scale = 1
+skirt_distance = 6
+skirt_height = 1
+skirts = 1
+slowdown_below_layer_time = 15
+small_perimeter_speed = 50
+solid_fill_pattern = rectilinear
+solid_infill_speed = 75
+solid_layers = 2
+start_gcode = G28 ; home all axes\nM92 X63 ; calibrate X\nM92 Y63  ; calibrate Y\nM92 Z2256  ; calibrate Z\nM92 E555  ; calibrate E
+support_material = 0
+support_material_tool = 0
+temperature = 220
+travel_speed = 130
+use_relative_e_distances = 0
+z_offset = 0.06

config_spool.ini

@@ -0,0 +1,67 @@
+acceleration = 0
+bed_size = 140,140
+bed_temperature = 95
+bottom_layer_speed_ratio = 0.3
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 75
+cooling = 0
+disable_fan_first_layers = 1
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid = 1,1
+end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\nM140 S0; turn off bed
+extrusion_axis = E
+extrusion_multiplier = 1
+extrusion_width_ratio = 0
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 2.75
+fill_angle = 45
+fill_density = 0.3
+fill_pattern = rectilinear
+first_layer_bed_temperature = 95
+first_layer_height_ratio = 1
+first_layer_temperature = 230
+g0 = 0
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor = reprap
+infill_acceleration = 50
+infill_every_layers = 1
+infill_speed = 75
+layer_gcode = 
+layer_height = 0.4
+max_fan_speed = 100
+min_fan_speed = 35
+min_print_speed = 10
+notes = 
+nozzle_diameter = 0.5
+output_filename_format = [input_filename_base].gcode
+perimeter_acceleration = 25
+perimeter_speed = 75
+perimeters = 2
+post_process = 
+print_center = 70,70
+retract_before_travel = 2
+retract_length = 1
+retract_lift = 0.4
+retract_restart_extra = 0
+retract_speed = 30
+rotate = 0
+scale = 1
+skirt_distance = 6
+skirt_height = 1
+skirts = 1
+slowdown_below_layer_time = 15
+small_perimeter_speed = 50
+solid_fill_pattern = rectilinear
+solid_infill_speed = 75
+solid_layers = 2
+start_gcode = G28 ; home all axes\nM92 X63 ; calibrate X\nM92 Y63  ; calibrate Y\nM92 Z2256  ; calibrate Z\nM92 E555  ; calibrate E
+support_material = 0
+support_material_tool = 0
+temperature = 220
+travel_speed = 130
+use_relative_e_distances = 0
+z_offset = 0.04

config_woman.ini

@@ -0,0 +1,72 @@
+acceleration = 0
+bed_size = 140,140
+bed_temperature = 95
+bottom_layer_speed_ratio = 0.3
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 75
+complete_objects = 0
+cooling = 0
+disable_fan_first_layers = 1
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid = 1,1
+end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\nM140 S0; turn off bed
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extrusion_axis = E
+extrusion_multiplier = 1
+extrusion_width_ratio = 0
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 2.75
+fill_angle = 45
+fill_density = 0.15
+fill_pattern = honeycomb
+first_layer_bed_temperature = 95
+first_layer_height_ratio = 1
+first_layer_temperature = 230
+g0 = 0
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor = reprap
+infill_acceleration = 50
+infill_every_layers = 1
+infill_speed = 75
+layer_gcode = 
+layer_height = 0.4
+max_fan_speed = 100
+min_fan_speed = 35
+min_print_speed = 10
+notes = 
+nozzle_diameter = 0.5
+output_filename_format = [input_filename_base].gcode
+perimeter_acceleration = 25
+perimeter_speed = 75
+perimeters = 2
+post_process = 
+print_center = 70,70
+randomize_start = 1
+retract_before_travel = 2
+retract_length = 1
+retract_lift = 0.4
+retract_restart_extra = 0
+retract_speed = 30
+rotate = 0
+scale = 1
+skirt_distance = 6
+skirt_height = 1
+skirts = 1
+slowdown_below_layer_time = 15
+small_perimeter_speed = 50
+solid_fill_pattern = rectilinear
+solid_infill_speed = 75
+solid_layers = 2
+start_gcode = G28 ; home all axes\nM92 X63 ; calibrate X\nM92 Y63  ; calibrate Y\nM92 Z2256  ; calibrate Z\nM92 E555  ; calibrate E
+support_material = 0
+support_material_tool = 0
+temperature = 210
+threads = 2
+travel_speed = 130
+use_relative_e_distances = 0
+z_offset = 0.06

configs_old/config.ini

@@ -0,0 +1,67 @@
+acceleration = 0
+bed_size = 140,140
+bed_temperature = 95
+bottom_layer_speed_ratio = 0.35
+bridge_fan_speed = 50
+bridge_flow_ratio = 1
+bridge_speed = 75
+cooling = 1
+disable_fan_first_layers = 60
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid = 1,1
+end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\nM140 S0; turn off bed
+extrusion_axis = E
+extrusion_multiplier = 1
+extrusion_width_ratio = 0
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 3.05
+fill_angle = 45
+fill_density = 0.3
+fill_pattern = rectilinear
+first_layer_bed_temperature = 95
+first_layer_height_ratio = 1
+first_layer_temperature = 240
+g0 = 0
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor = reprap
+infill_acceleration = 50
+infill_every_layers = 1
+infill_speed = 75
+layer_gcode = 
+layer_height = 0.4
+max_fan_speed = 50
+min_fan_speed = 25
+min_print_speed = 10
+notes = 
+nozzle_diameter = 0.5
+output_filename_format = [input_filename_base].gcode
+perimeter_acceleration = 25
+perimeter_speed = 75
+perimeters = 1
+post_process = 
+print_center = 50,70
+retract_before_travel = 2
+retract_length = 1
+retract_lift = 0.4
+retract_restart_extra = 0
+retract_speed = 30
+rotate = 0
+scale = 1
+skirt_distance = 6
+skirt_height = 1
+skirts = 1
+slowdown_below_layer_time = 10
+small_perimeter_speed = 50
+solid_fill_pattern = rectilinear
+solid_infill_speed = 75
+solid_layers = 2
+start_gcode = G28 ; home all axes\nM92 X63 ; calibrate X\nM92 Y63  ; calibrate Y\nM92 Z2400  ; calibrate Z\nM92 E799.1546391  ; calibrate E
+support_material = 0
+support_material_tool = 0
+temperature = 220
+travel_speed = 195
+use_relative_e_distances = 1
+z_offset = 0.12

configs_old/config2.ini

@@ -0,0 +1,67 @@
+acceleration = 0
+bed_size = 200,200
+bed_temperature = 70
+bottom_layer_speed_ratio = 0.30
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 30
+cooling = 0
+disable_fan_first_layers = 1
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid = 1,1
+end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors
+extrusion_axis = E
+extrusion_multiplier = 1
+extrusion_width_ratio = 0
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 3
+fill_angle = 45
+fill_density = 0.5
+fill_pattern = rectilinear
+first_layer_bed_temperature = 70
+first_layer_height_ratio = 1
+first_layer_temperature = 230
+g0 = 0
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor = reprap
+infill_acceleration = 50
+infill_every_layers = 1
+infill_speed = 30
+layer_gcode = 
+layer_height = 0.4
+max_fan_speed = 100
+min_fan_speed = 35
+min_print_speed = 10
+notes = 
+nozzle_diameter = 0.5
+output_filename_format = [input_filename_base].gcode
+perimeter_acceleration = 25
+perimeter_speed = 30
+perimeters = 2
+post_process = 
+print_center = 50,50
+retract_before_travel = 2
+retract_length = 1
+retract_lift = 0
+retract_restart_extra = 0
+retract_speed = 30
+rotate = 0
+scale = 2
+skirt_distance = 6
+skirt_height = 2
+skirts = 2
+slowdown_below_layer_time = 15
+small_perimeter_speed = 30
+solid_fill_pattern = rectilinear
+solid_infill_speed = 30
+solid_layers = 3
+start_gcode = G28 ; home all axes\nM92 X62.807427931325 ; calibrate X\nM92 Y62.807427931325  ; calibrate Y\nM92 Z2311.89372147448  ; calibrate Z\nM92 E799.1546391  ; calibrate E
+support_material = 0
+support_material_tool = 0
+temperature = 220
+travel_speed = 195
+use_relative_e_distances = 1
+z_offset = 0.25

configs_old/config_back.ini

@@ -0,0 +1,67 @@
+acceleration = 0
+bed_size = 200,200
+bed_temperature = 77
+bottom_layer_speed_ratio = 0.35
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 30
+cooling = 0
+disable_fan_first_layers = 1
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid = 1,1
+end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors
+extrusion_axis = E
+extrusion_multiplier = 1
+extrusion_width_ratio = 0
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 3
+fill_angle = 45
+fill_density = 0.4
+fill_pattern = rectilinear
+first_layer_bed_temperature = 77
+first_layer_height_ratio = 1
+first_layer_temperature = 230
+g0 = 0
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor = reprap
+infill_acceleration = 50
+infill_every_layers = 1
+infill_speed = 30
+layer_gcode = 
+layer_height = 0.4
+max_fan_speed = 100
+min_fan_speed = 35
+min_print_speed = 10
+notes = 
+nozzle_diameter = 0.5
+output_filename_format = [input_filename_base].gcode
+perimeter_acceleration = 25
+perimeter_speed = 30
+perimeters = 1
+post_process = 
+print_center = 50,50
+retract_before_travel = 2
+retract_length = 1.5
+retract_lift = 0
+retract_restart_extra = 0
+retract_speed = 30
+rotate = 0
+scale = 1
+skirt_distance = 6
+skirt_height = 5
+skirts = 2
+slowdown_below_layer_time = 15
+small_perimeter_speed = 30
+solid_fill_pattern = rectilinear
+solid_infill_speed = 30
+solid_layers = 3
+start_gcode = G28 ; home all axes\nM92 X62.807427931325 ; calibrate X\nM92 Y62.807427931325  ; calibrate Y\nM92 Z2311.89372147448  ; calibrate Z\nM92 E799.1546391  ; calibrate E
+support_material = 0
+support_material_tool = 0
+temperature = 220
+travel_speed = 195
+use_relative_e_distances = 1
+z_offset = 0.22

configs_old/config_hollow.ini

@@ -0,0 +1,67 @@
+acceleration = 0
+bed_size = 140,140
+bed_temperature = 77
+bottom_layer_speed_ratio = 0.35
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 30
+cooling = 1
+disable_fan_first_layers = 3
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid = 1,1
+end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\nM140 S0; turn off bed
+extrusion_axis = E
+extrusion_multiplier = 1
+extrusion_width_ratio = 0
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 3.05
+fill_angle = 45
+fill_density = 0
+fill_pattern = rectilinear
+first_layer_bed_temperature = 77
+first_layer_height_ratio = 2
+first_layer_temperature = 230
+g0 = 0
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor = reprap
+infill_acceleration = 50
+infill_every_layers = 1
+infill_speed = 50
+layer_gcode = 
+layer_height = 0.2
+max_fan_speed = 100
+min_fan_speed = 50
+min_print_speed = 10
+notes = 
+nozzle_diameter = 0.5
+output_filename_format = [input_filename_base].gcode
+perimeter_acceleration = 25
+perimeter_speed = 50
+perimeters = 2
+post_process = 
+print_center = 50,70
+retract_before_travel = 2
+retract_length = 1
+retract_lift = 0.4
+retract_restart_extra = 0
+retract_speed = 30
+rotate = 0
+scale = 1
+skirt_distance = 6
+skirt_height = 1
+skirts = 1
+slowdown_below_layer_time = 15
+small_perimeter_speed = 30
+solid_fill_pattern = rectilinear
+solid_infill_speed = 40
+solid_layers = 2
+start_gcode = G28 ; home all axes\nM92 X62.807427931325 ; calibrate X\nM92 Y62.807427931325  ; calibrate Y\nM92 Z2311.89372147448  ; calibrate Z\nM92 E799.1546391  ; calibrate E
+support_material = 0
+support_material_tool = 0
+temperature = 220
+travel_speed = 195
+use_relative_e_distances = 1
+z_offset = 0.45

configs_old/config_kapton.ini

@@ -0,0 +1,67 @@
+acceleration = 0
+bed_size = 200,200
+bed_temperature = 77
+bottom_layer_speed_ratio = 0.35
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 30
+cooling = 0
+disable_fan_first_layers = 1
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid = 1,1
+end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors
+extrusion_axis = E
+extrusion_multiplier = 1
+extrusion_width_ratio = 0
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 3
+fill_angle = 45
+fill_density = 0.4
+fill_pattern = rectilinear
+first_layer_bed_temperature = 77
+first_layer_height_ratio = 1
+first_layer_temperature = 230
+g0 = 0
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor = reprap
+infill_acceleration = 50
+infill_every_layers = 1
+infill_speed = 30
+layer_gcode = 
+layer_height = 0.4
+max_fan_speed = 100
+min_fan_speed = 35
+min_print_speed = 10
+notes = 
+nozzle_diameter = 0.5
+output_filename_format = [input_filename_base].gcode
+perimeter_acceleration = 25
+perimeter_speed = 30
+perimeters = 1
+post_process = 
+print_center = 50,50
+retract_before_travel = 2
+retract_length = 1.5
+retract_lift = 0
+retract_restart_extra = 0
+retract_speed = 30
+rotate = 0
+scale = 1
+skirt_distance = 6
+skirt_height = 5
+skirts = 2
+slowdown_below_layer_time = 15
+small_perimeter_speed = 30
+solid_fill_pattern = rectilinear
+solid_infill_speed = 30
+solid_layers = 3
+start_gcode = G28 ; home all axes\nM92 X62.807427931325 ; calibrate X\nM92 Y62.807427931325  ; calibrate Y\nM92 Z2311.89372147448  ; calibrate Z\nM92 E799.1546391  ; calibrate E
+support_material = 0
+support_material_tool = 0
+temperature = 220
+travel_speed = 195
+use_relative_e_distances = 1
+z_offset = 0.22

configs_old/config_mulher.ini

@@ -0,0 +1,67 @@
+acceleration = 0
+bed_size = 140,140
+bed_temperature = 85
+bottom_layer_speed_ratio = 0.35
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 75
+cooling = 1
+disable_fan_first_layers = 30
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid = 1,1
+end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\nM140 S0; turn off bed
+extrusion_axis = E
+extrusion_multiplier = 1
+extrusion_width_ratio = 0
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 3.00
+fill_angle = 45
+fill_density = 0.1
+fill_pattern = rectilinear
+first_layer_bed_temperature = 85
+first_layer_height_ratio = 1
+first_layer_temperature = 230
+g0 = 0
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor = reprap
+infill_acceleration = 50
+infill_every_layers = 1
+infill_speed = 75
+layer_gcode = 
+layer_height = 0.2
+max_fan_speed = 100
+min_fan_speed = 50
+min_print_speed = 10
+notes = 
+nozzle_diameter = 0.5
+output_filename_format = [input_filename_base].gcode
+perimeter_acceleration = 25
+perimeter_speed = 75
+perimeters = 1
+post_process = 
+print_center = 40,40
+retract_before_travel = 2
+retract_length = 1
+retract_lift = 0.2
+retract_restart_extra = 0
+retract_speed = 30
+rotate = 0
+scale = 1
+skirt_distance = 6
+skirt_height = 1
+skirts = 1
+slowdown_below_layer_time = 15
+small_perimeter_speed = 75
+solid_fill_pattern = rectilinear
+solid_infill_speed = 75
+solid_layers = 3
+start_gcode = G28 ; home all axes\nM92 X62.807427931325 ; calibrate X\nM92 Y62.807427931325  ; calibrate Y\nM92 Z2311.89372147448  ; calibrate Z\nM92 E799.1546391  ; calibrate E
+support_material = 0
+support_material_tool = 0
+temperature = 220
+travel_speed = 195
+use_relative_e_distances = 1
+z_offset = 0.08

configs_old/dos.ini

@@ -0,0 +1,65 @@
+acceleration = 0
+bed_temperature = 98
+bottom_layer_speed_ratio = 0.35
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 60
+cooling = 0
+disable_fan_first_layers = 1
+duplicate_distance = 6
+duplicate_x = 1
+duplicate_y = 1
+end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors
+extrusion_axis = E
+extrusion_multiplier = 1
+extrusion_width_ratio = 0
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 3
+fill_angle = 45
+fill_density = 0.4
+fill_pattern = rectilinear
+first_layer_bed_temperature = 98
+first_layer_height_ratio = 1
+first_layer_temperature = 220
+g0 = 0
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor = reprap
+infill_acceleration = 50
+infill_every_layers = 1
+infill_speed = 80
+layer_height = 0.4
+max_fan_speed = 100
+min_fan_speed = 35
+min_print_speed = 10
+notes = 
+nozzle_diameter = 0.5
+output_filename_format = [input_filename_base].gcode
+perimeter_acceleration = 25
+perimeter_speed = 65
+perimeters = 2
+post_process = 
+print_center = 50,50
+retract_before_travel = 2
+retract_length = 1
+retract_lift = 0
+retract_restart_extra = 0
+retract_speed = 30
+rotate = 0
+scale = 1
+skirt_distance = 6
+skirt_height = 1
+skirts = 2
+slowdown_below_layer_time = 15
+small_perimeter_speed = 30
+solid_fill_pattern = rectilinear
+solid_infill_speed = 70
+solid_layers = 3
+start_gcode = G28 ; home all axes\nM92 X64.8592 ; calibrate X\nM92 Y64.8592  ; calibrate Y\nM92 Z2387.0719  ; calibrate Z\nM92 E569  ; calibrate E
+support_material = 0
+support_material_tool = 0
+temperature = 210
+travel_speed = 195
+use_relative_e_distances = 1
+z_offset = 0